9489 Posts - Page: Previous | 1 | ... | 306 | 307 | 308 | 309 | 310 | 311 | 312 | 313 | ... | 475 | Next

Recent Posts for the Entire Site

ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6161 | Friday, 04-May 2012 @ 9:35pm
"oh yea i remember reading that some on 1200.com, so the vanette stuff is fairly common?"
Upper Balljoint Compatability  |  Read full post
d
Oz + JPN
Joined: 23-Apr 2011
1432 posts
Post #6162 | Friday, 04-May 2012 @ 8:49pm
"Just to let you know Neil years ago told me about the a15 vanette front end can be used in a 1000 if you reverse the stub axles basically to have the steering knuckles facing the back rather than the front. This would allow you to use the late vanette..."
Upper Balljoint Compatability  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6163 | Friday, 04-May 2012 @ 6:09pm
"i've decided my plan is to get the gear, set it up for the thou ball joint.   because i dont think there will be much of a market for these custom arms im not getting carried away with them as soon as i finished doing my custom arms i'll look into a..."
Upper Balljoint Compatability  |  Read full post
Mauricio
Guatemala, central america
Joined: 15-Dec 2011
7 posts
Post #6164 | Friday, 04-May 2012 @ 3:47pm
"You sell the weber?"
Twin webber setup  |  Read full post
d
Oz + JPN
Joined: 23-Apr 2011
1432 posts
Post #6165 | Friday, 04-May 2012 @ 9:44am
"I mean on an original 1000"
Upper Balljoint Compatability  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
492 posts
Post #6166 | Thursday, 03-May 2012 @ 8:19pm
"Torana stubs and balljoints   Neither same as Datto"
Upper Balljoint Compatability  |  Read full post
d
Oz + JPN
Joined: 23-Apr 2011
1432 posts
Post #6167 | Thursday, 03-May 2012 @ 6:13pm
"Arent the upper or lowers the same part no. as the 80s vanettes with the A series engines? Im positive they are."
Upper Balljoint Compatability  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6168 | Thursday, 03-May 2012 @ 12:45pm
"Are they 1000 knuckles neil? "
Upper Balljoint Compatability  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
492 posts
Post #6169 | Thursday, 03-May 2012 @ 9:13am
Edited by Neil
Thursday, 03-May 2012 @ 9:14am
"My old racecar But it had Torana upper balljoints and stubs     "
Upper Balljoint Compatability  |  Read full post
SharmCos
Malaysia
Joined: 17-Oct 2011
18 posts
Post #6170 | Wednesday, 02-May 2012 @ 10:47pm
"FYI a pair of ball joints will cost AUD150 shipped to Australia by airmail."
F/S: New B10 Bits - ball joints and tie rod ends  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6171 | Wednesday, 02-May 2012 @ 9:41pm
"dunno hey im not sure how they measure it, found gm have 1 1/2 degree taper poor foot and found a reamer tool for that just not sure of the dimension of the king pin.    having a hard time finding a metric reamer taper tool   it could be standard its just..."
Upper Balljoint Compatability  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #6172 | Wednesday, 02-May 2012 @ 9:27pm
Edited by beetwenty
Wednesday, 02-May 2012 @ 9:28pm
"Thinking about those numbers...   12.3mm - 11mm = 1.3mm gain over 13.5mm length.   So roughly 10:1  eg 10mm length changes 1mm diammeter. Do you think that could be a standard taper size? It sounds as if it could be a metric standard? if such a thing..."
Upper Balljoint Compatability  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6173 | Wednesday, 02-May 2012 @ 9:13pm
"sweet thanks ash gives an idea of its size i dont actually have any at my house to measure"
Upper Balljoint Compatability  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #6174 | Wednesday, 02-May 2012 @ 9:02pm
Edited by beetwenty
Wednesday, 02-May 2012 @ 9:39pm
"   I just measured one of the 555 ones like in the pic above. Measurements I got were...top 11mm - base 12.3mm tapering down over a distance of 13.5mm.   The rubber boot made things hard to measure, (It's a tough little sucker).   Those numbers should get..."
Upper Balljoint Compatability  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6175 | Wednesday, 02-May 2012 @ 8:50pm
"main reason is just to get the geometry right and that it would actually be viable for street use.   well i'll have to go down to the local repco or something and see what they have similar to the thou one   does anyone know the taper/size of the b10..."
Upper Balljoint Compatability  |  Read full post
Davoo
SA
Joined: 22-Feb 2011
12 posts
Post #6176 | Wednesday, 02-May 2012 @ 8:12pm
"  Hey all as Title said twin webber setup for E.O.L/for sale Anyone keen ????   0416634622 Dave"
Twin webber setup  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
492 posts
Post #6177 | Wednesday, 02-May 2012 @ 8:08pm
"Why make it to suit a balljoint thats NLA ?   I'd be picking something readily available like a Torana upper BJ that bolts in with 4 bolts.... if the taper is close enough or the stub is reamable"
Upper Balljoint Compatability  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #6178 | Wednesday, 02-May 2012 @ 7:25pm
"there's been talk of these on 1200.com and i think there is a difference i just can't think of what it was"
Cross flow head, Will it fit?  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #6179 | Wednesday, 02-May 2012 @ 7:22pm
"Does anyone know if a "Mini A-series head" would fit a "Datsun A-series Block"? Im not after one of these, I don't have the money to build an engine. Im just curious if it would fit.  ..."
Cross flow head, Will it fit?  |  Read full post
combo1000
geelong victoria australia
Joined: 22-May 2011
44 posts
Post #6180 | Wednesday, 02-May 2012 @ 6:23pm
"thanks pm'd mate"
Upper Balljoint Compatability  |  Read full post
9489 Posts - Page: Previous | 1 | ... | 306 | 307 | 308 | 309 | 310 | 311 | 312 | 313 | ... | 475 | Next