9489 Posts - Page: Previous | 1 | ... | 467 | 468 | 469 | 470 | 471 | 472 | 473 | 474 | 475 | Next

Recent Posts for the Entire Site

subwoofers
Vancouver B.C
Joined: 11-Feb 2011
35 posts
Post #9401 | Saturday, 12-Feb 2011 @ 4:37am
Edited by subwoofers
Saturday, 12-Feb 2011 @ 4:38am
"1) Pair of "Datsun" badges that go on the front fenders of the 1000 Deluxe above the shields. 2) Fender mounted mirrors Thanks! My car is so close to being complete."
Need some little parts  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9402 | Friday, 11-Feb 2011 @ 11:38pm
"PM sent."
parts needed in canada  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #9403 | Friday, 11-Feb 2011 @ 11:07pm
"yea it helps heaps that's pretty well is what i done last time, order was a bit different tho. thanks for the advice i want to take the front end out of the 2dr and restore it for my ute so i want minimal damage"
pulling the front end apart?  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9404 | Friday, 11-Feb 2011 @ 10:32pm
"Is this any help to you Leith? "
pulling the front end apart?  |  Read full post
clyons8
Rabaul, Papua New Guinea
Joined: 10-Feb 2011
458 posts
Post #9405 | Friday, 11-Feb 2011 @ 10:11pm
"Yeah okay with lining them up you normally leave the single adjusting bolt (on the other end) loose so you have a bit of play and this tends to helpwith getting it back into place. You can also jack up the underside of that LCA to put it at a height..."
pulling the front end apart?  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #9406 | Friday, 11-Feb 2011 @ 10:06pm
"yea i think it is chris, is it easier to take the castor rod out with it still attached to the LCA when the LCA has been disconnected from the stub and chassis?? the problem i have is putting the castor rod back in trying to line the bolts up that go..."
pulling the front end apart?  |  Read full post
clyons8
Rabaul, Papua New Guinea
Joined: 10-Feb 2011
458 posts
Post #9407 | Friday, 11-Feb 2011 @ 10:06pm
Edited by clyons8
Friday, 11-Feb 2011 @ 10:06pm
"Okay, this has done an entire back-flip. I looked into getting these copied and cast but it's turning into a nightmare, I am now making the badges myself running off the original plan of a laser-cut layered format. I just haven't had the time to chase..."
Datsun 1000 Boot Badges  |  Read full post
clyons8
Rabaul, Papua New Guinea
Joined: 10-Feb 2011
458 posts
Post #9408 | Friday, 11-Feb 2011 @ 9:58pm
"Is the castor rod the radius rod? Same thing? Sometimes if they're loose or if the bushings at the end have perished the nut will cross a thread or two, so basically it's a matter of getting it off and hoping that a new nut will be able to thread back..."
pulling the front end apart?  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9409 | Friday, 11-Feb 2011 @ 9:46pm
Edited by beetwenty
Friday, 11-Feb 2011 @ 9:49pm
"Just winding in and out in small steps with heaps of inox is what I have found works best. The only other things I can suggest is to use a 6 point socket or 6 point ring spanner and give the breaker bar/spanner a sharp hit with a rubber mallet to get..."
pulling the front end apart?  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #9410 | Friday, 11-Feb 2011 @ 9:24pm
"yea i always inox them before some are just a prick, the main one i'd like to know is the castor rod"
pulling the front end apart?  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9411 | Friday, 11-Feb 2011 @ 9:15pm
"I would be interested to know how to do it properley as well. When I did mine I cut it off the front end that I had from a rusty 1K, so care wasn't an issue. For the nuts I would suggest drowning them in inox and letting it sit for a while to let the..."
pulling the front end apart?  |  Read full post
andrewzuku
Maryborough QLD, Australia
Joined: 10-Feb 2011
130 posts
Post #9412 | Friday, 11-Feb 2011 @ 9:04pm
Edited by admin
Saturday, 31-Dec 2011 @ 5:14pm
"Ok, I've made the following changes... Joined date and post count are displayed under member's avatars Post count is clickable to view a members previous posts Login is now on every page of the forum The 3 most recent posts are on the main page with a..."
Members Profile Display  |  Read full post
ThouUte
Toowoomba QLD
Joined: 10-Feb 2011
565 posts
Post #9413 | Friday, 11-Feb 2011 @ 9:02pm
"Hi guys im gonna pull the front end outta the 2dr i got and need to know the easiest way. last time i done it on the ute it took forever and it always seemed to be under load so it was hard to undo nut and what not (think i stripped a couple) so would..."
pulling the front end apart?  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9414 | Friday, 11-Feb 2011 @ 6:58pm
"The plan for my ute so far is to keep it original except for an A12 in place of the stock A10. I have changed the radio to a modern one that has an old look to it, I will do the same with the seatbelts. There is a company called Retro Belt that I am..."
1969 Datsun B20, Restoration  |  Read full post
ratb10
Sydney
Joined: 11-Feb 2011
152 posts
Post #9415 | Friday, 11-Feb 2011 @ 6:33pm
"This is an insanely good write up, keep it up. Are you going back to original or are you going to have some modifications too?"
1969 Datsun B20, Restoration  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9416 | Friday, 11-Feb 2011 @ 6:24pm
Edited by beetwenty
Friday, 11-Feb 2011 @ 6:26pm
"I'll contribute to this. Datsun 521 part number 26160-B0101 is identical to the 1000 1968/1969 short spear lamp. Datsun 1600 is the same as Long spear 1970 1000 Datsun 410 and 411 Headlamp Switch is the same as 1000 Datsun 520 reverse lamp is the..."
Parts that are interchangable with other Datsuns  |  Read full post
ratb10
Sydney
Joined: 11-Feb 2011
152 posts
Post #9417 | Friday, 11-Feb 2011 @ 5:48pm
Edited by admin
Saturday, 31-Dec 2011 @ 5:14pm
"I thought this would be a good idea to put up, and then everyone who drops by could contribute something if they have used parts from other Datsuns, or even any other make, as long as it fits. So far parts that have worked for me: Datsun Stanza 1980..."
Parts that are interchangable with other Datsuns  |  Read full post
clyons8
Rabaul, Papua New Guinea
Joined: 10-Feb 2011
458 posts
Post #9418 | Friday, 11-Feb 2011 @ 5:28pm
Edited by clyons8
Friday, 11-Feb 2011 @ 5:34pm
"Location: Adelaide, SoUF OstrAiya Item: A12 Engine 1200cc Item Condition: Freshly Rebuilt Extra Info: Engine Mounts (direct bolt-in) Full Floating Flat Top Pistons 1.5mm OS Balanced from front to back (crank pulley to clutch pp) Ported and faced H75..."
Heavily Worked A12 To suit Datsun 1000  |  Read full post
beetwenty
Gold Coast, Australia
Joined: 05-Feb 2011
1191 posts
Post #9419 | Friday, 11-Feb 2011 @ 5:12pm
"I appreciate it. With regards to the pics, your scanner should be fine. some of the pics started pretty ordinary, photoshop does wonders. If you do scan, 150 or 300 dpi is fine. The for sale section seems to work, i have sold 2 items in less than 1 day."
Welcome to datsun1000.com  |  Read full post
clyons8
Rabaul, Papua New Guinea
Joined: 10-Feb 2011
458 posts
Post #9420 | Friday, 11-Feb 2011 @ 5:07pm
"No worries, if my scanner is any good I'll email them otherwise I'll send them so that they will at least look like the rest of the submissions. Site is awesome, there were a couple alternate sites that came up some years ago but they lacked any interest..."
Welcome to datsun1000.com  |  Read full post
9489 Posts - Page: Previous | 1 | ... | 467 | 468 | 469 | 470 | 471 | 472 | 473 | 474 | 475 | Next