15 Posts - Page: 1

All 1000's, Disk conversion

Hi all, I purchased a conversion kit from MADDAT in South Aus and was one of the easiest kits to fit. It has skyline disks with commodore cal's and all brackets and hardware required. Awesome kit!
Do your 13 inch wheels fit any pics before you put them on?
whichmodel  skyline disks and com calipers?
During times of universal deceit, telling the truth becomes a revolutionary act, Big Brother is watching you - George Orwell 'Most Jews do not like to admit it, but our god is Lucifer -- so I wasn't lying -- and we are his chosen people. Lucifer is very much alive.'"  Harold Rosenthal http://www.thetruthseeker.co.uk/?p=24688
No sorry d I wasn't organised enough to get photos prior, calipers are VT and as for disks I'm not sure. I was always putting 14" rims so that's what the kit was made for. I will try and update some photos of my build in my profile. Car is in nth melbourne and not going till tomorrow
Calipers actually appear to be VB-VP
I'd like to get the part # of the discs if you can let me know
Its roll marked on the outer edge of the disc (if the discs isn't machined down) incase they weren't in labelled boxes
Well p sounds like t over phone haha...my kit is about two and a half yrs old now so I'm a bit sketchy. I'm going to panel shop tomorrow so will get no's then. Hope this helps Neil
Champion
During times of universal deceit, telling the truth becomes a revolutionary act, Big Brother is watching you - George Orwell 'Most Jews do not like to admit it, but our god is Lucifer -- so I wasn't lying -- and we are his chosen people. Lucifer is very much alive.'"  Harold Rosenthal http://www.thetruthseeker.co.uk/?p=24688
Hey all, the code off the disk is 3264 min thk 20 followed by 3w. Hope this is what you want. Tried to upload pic but some error has occurred in my gallery 

 
Got issue with pics sorted (thanks Ash) this is the rotor used for my conversion.
Looks good now we wait for the resident brake Guru to show us the light and wisdom cause sure as hell could not find the part number on the DBA catalogue
During times of universal deceit, telling the truth becomes a revolutionary act, Big Brother is watching you - George Orwell 'Most Jews do not like to admit it, but our god is Lucifer -- so I wasn't lying -- and we are his chosen people. Lucifer is very much alive.'"  Harold Rosenthal http://www.thetruthseeker.co.uk/?p=24688
Not a DBA or RDA number
Infact its not a number I've seen before
If I had a few measurements I could nut it out
 
Total height , centre hole would help... I assume diam is per their site at 256mm
 
My first thought was Magna... but maybe not ... might be a Toyo disc
A quick google search for that part number brings up this...
http://www.ebay.com/itm/Aimco-3264-Front-Disc-Brake-Rotor-/251129555065?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item3a787ce879
 
This is what I came up with after another google search.
Brembo 09.5449.14

Has a Dia of 256.5mm, Min thickness of 20mm and is 4x114.3mm PCD

 
http://www.bremboaftermarket.com/En/Car_Disc_Catalogue/Catalogue_Detail.aspx?ApplicationIDMaster=15721


 
 
It is not slotted on the braking surface, but im sure with a little more searching there would be both options.
 
Do you think these sizes look right?
1967 Datsun B10 2 Door.
Just measured them at 256mm so that would seem right. Cannot get offset as car is on jig at moment!
Looks like a DBA617 off an N16 Pulsar then
Awesome, we will get to bottom of it eventually!
slotted version of the Nissan 1995 infiniti (n15?) "Aimco 3264 Front Disc"

  • 1995 INFINITI G20 Front Brake Rotor

  • Category: Front Brake Rotor
  • Description: Extreme Service Performance Brake Rotor part for  1991-1996 INFINITI G20 with ENGINE-- L4-1998cc 2.0L F/I Vin SR20DE
  • Manufacturer: AIMCO


  • During times of universal deceit, telling the truth becomes a revolutionary act, Big Brother is watching you - George Orwell 'Most Jews do not like to admit it, but our god is Lucifer -- so I wasn't lying -- and we are his chosen people. Lucifer is very much alive.'"  Harold Rosenthal http://www.thetruthseeker.co.uk/?p=24688
    15 Posts - Page: 1