488 Posts - Page: 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | ... | 25 | Next

Neil's Posts

Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #1 | Tuesday, 26-Sep 2023 @ 9:36pm
"Hope you had a good day mate   We should catch up soon"
Distinguished Gentlemen's Drive  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #2 | Wednesday, 05-Jul 2023 @ 8:37pm
"Are you stretching the alloy housing ? I hurt a few in my old racer If you go to a cast iron pumpkin from a 1200 its a bit stronger Then 3.9 is easy to get"
4.111 diff ratio, hard to get?  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #3 | Monday, 03-Jul 2023 @ 8:12pm
"1000 Coupe are 4.11 Bill"
4.111 diff ratio, hard to get?  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #4 | Thursday, 28-Apr 2022 @ 9:19pm
"Doubt it would heat much Very small unit Might work ok as a demister"
Heater solution  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #5 | Monday, 10-Jan 2022 @ 7:53pm
"Might have to get some gas for my TIG one day   Looking good"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #6 | Thursday, 23-Dec 2021 @ 10:22pm
"Not bad   Hows it sound ?"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #7 | Monday, 11-Oct 2021 @ 8:27pm
"Going well   Wish one of mine was driveable "
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #8 | Tuesday, 05-Oct 2021 @ 9:09pm
Edited by Neil
Tuesday, 05-Oct 2021 @ 9:10pm
"https://www.youtube.com/watch?v=0tzWC2G3mr0 https://www.youtube.com/watch?v=PPYNCt5yV-U   Posting links here sucks "
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #9 | Monday, 04-Oct 2021 @ 8:27pm
"Can you not put the alt back down low on the passengers side ?"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #10 | Friday, 01-Oct 2021 @ 9:24pm
"Did the same on my wagoon years ago My mech machined down some tube he had in the shed No idea on length though"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #11 | Thursday, 30-Sep 2021 @ 7:56pm
"Much betterer   I like it   In the past when I used to make and sell my conversions using the KC laser calipers I always had to scrounge up clutch masters to rob the rods out of Only Toyota ones... so no biggie"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #12 | Tuesday, 21-Sep 2021 @ 8:06pm
"So basically that lovely rod you made Make a longer pin to screw into your clevis And delete the captive washer   You'll need to make your rod long enough to have about 20-40 thou clearance into the back of the cyl when assembled"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #13 | Monday, 20-Sep 2021 @ 8:04pm
"From memory when I removed them on the wagon Small nuts on the back of the trims So yes... locating and unscrewing is the go"
How to Remove Dash Trim Strips - Late (Wide) Version  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #14 | Monday, 20-Sep 2021 @ 7:50pm
"Careful with those rods The bigger cyls are designed to run on a booster And if you put a non boosted rod up their bum the first piston can hold down Not allowing it to bleed properly or return enough So holds the brakes on   When I do my disc setups I..."
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #15 | Tuesday, 14-Sep 2021 @ 7:57pm
"Good stuff"
Early Torana Shocks on Coupe Brackets  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #16 | Monday, 13-Sep 2021 @ 8:03pm
"Bodgy mounts are us Thats the way most people do it as there is no bolt on avail mount"
A Series Engine Mounts  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #17 | Monday, 13-Sep 2021 @ 8:03pm
"7/8 should work fine Depending where you like your pedal to be and its feel   I've run 11/16 . 3/4 . 13/16 and  7/8 on various cars"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #18 | Friday, 27-Aug 2021 @ 8:03pm
"Or this   [size= 15px]https://page.auctions.yahoo.co.jp/jp/auction/d520374209[/size] [size= 15px] [/size] [size= 15px] [/size]"
Datsun 1000 predecessor  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #19 | Wednesday, 11-Aug 2021 @ 9:21pm
"Might not be an issue Haven't done my rear conversion as yet"
Beetwenty's B10 2 door  |  Read full post
Neil
Perth Western Australia
Joined: 03-Mar 2011
488 posts
Post #20 | Monday, 09-Aug 2021 @ 8:01pm
"Are you putting a plate between diff flange and axle flange plate To take up the distance the drum backing plate used to occupy To stop end float of the axle ?"
Beetwenty's B10 2 door  |  Read full post
488 Posts - Page: 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | ... | 25 | Next