16 Posts - Page: 1

Datzon's Posts

Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #1 | Sunday, 10-Nov 2019 @ 7:15am
"Hey. Its been a while Sorry to the guys I haven't replied to. I've been tangled up with stuff. Getting back to what needs to be done. Needing to know if anyone out there knows how to hook up a CA18de vacuum solenoid valve. I have the vacuum tank, valve,..."
ca18de  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #2 | Tuesday, 10-Mar 2015 @ 6:59pm
"Has anyone put a remote brake booster in. I have a CA18 in my 1000 and have run out of room to fit one behind my master cylinder. I have VL callipers on the front with pulsar discs and a proportional valve for the rear brakes. They work as it is but I..."
remote brake booster setup  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #3 | Tuesday, 17-Sep 2013 @ 4:53pm
"I'll try and get some, a bit flat out lately. The steering box bolts right on,the only thing needed to do is fab up a plate on to existing column mount so as the new backet can be mounted. The shaft of the column is thinker so the boot rubber that goes..."
Advice on a Steering Column Swap  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #4 | Tuesday, 17-Sep 2013 @ 4:40pm
"Are you still looking for door frames?"
WTB KB10 door top door frames.  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #5 | Tuesday, 17-Sep 2013 @ 4:36pm
"I have some side draft delortos, (not sure what size they are, may be 40mm) if thats any good."
40mm Webers off a datsun 1600  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #6 | Monday, 16-Sep 2013 @ 7:49pm
"I'm doing a conversion and have put a surge tank and fuel pumps in the boot of my 1K (a bit prematurely) with out taking into consideration of seaealing off the boot from the cab to prevent fumes.  Just wondering if anyone has done this and if I can put..."
Fuel pumps in boot  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #7 | Monday, 16-Sep 2013 @ 7:27pm
"I've put a 120y collapsible column in my 1K. The only thing I did was fab up a plate for the braket top support."
Advice on a Steering Column Swap  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #8 | Saturday, 12-Jan 2013 @ 3:15pm
"I'ved used pulsar discs and VL calipers, with a proportional valve for the back brakes.  At a later date I think I will look for an upgrade to the rear."
Anyone got any photos of the front suspension on a 1k?  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #9 | Saturday, 12-Jan 2013 @ 3:01pm
"Iv'e got a S13 CA18 in a two door sedan.  Where i'm from that is the largest no aspro. engine I was allowed.  I thought about a 10A rotory but that was even too big.  In saying that I half way through it, like yourself, so hopefully someone will pass it."
new comer, got a few 1000 questions  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #10 | Saturday, 12-Jan 2013 @ 2:51pm
"All I did was cut about 15mm from the sump and packed the cross member about 5mm and I was able to fit it in under the bonet.  I was going to put an A15 in it but like you said the amount of upgrades, had to weigh up the reliability of an A series to the..."
CA in 1000  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #11 | Thursday, 15-Nov 2012 @ 5:33am
"Air box sorted.  I got a place called Tridant Plastics to make me up one.  Fits well.  Also took the car to get it wired up, whole new harness from front to back.  The only problem is that I need the vaccum gear for the secondary butterfly.The car revs..."
CA in 1000  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #12 | Tuesday, 12-Jun 2012 @ 9:50pm
"Here is how much room I have.  will have to right angle it, air flow meter will make it hard due to the amount of room I have, but also need room for a few vacum hoses.  Need to know how much of a pod filter needs to be covered up.  I'll go & find a small..."
CA in 1000  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #13 | Monday, 07-May 2012 @ 4:55pm
"G'day Phill, I may have some ball joints, depends on what ones you need.  I'm from North Rothbury, give me a ring. You have my number. Matt"
WANTED  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #14 | Tuesday, 27-Mar 2012 @ 5:05pm
"Sorry  guys, I havn't had the time to reply.  I have enough room for a master cylinder and clutch cylinder in the engine bay, all done & dusted.  Its the room I have for an air box to put my filter in.  Once again i'll post some pics to show whats going..."
CA in 1000  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #15 | Monday, 26-Mar 2012 @ 3:01pm
"Not much room left so I need to fab an intake up. Its not turbo, engineer would engineer it if it was.  I'll try and find the time to take more pics and post them up."
CA in 1000  |  Read full post
Datzon
Hunter Valley Australia
Joined: 21-Mar 2012
16 posts
Post #16 | Wednesday, 21-Mar 2012 @ 3:11pm
"Just wondering if anyone would have any ideas about a air intake setup for a CA18 into a 1000.  I've hit a wall, need some different ideas.   ."
CA in 1000  |  Read full post
16 Posts - Page: 1