Recent Posts for the Entire Site

Gold Coast, Australia

Joined: 05-Feb 2011

"Yes, I sand blasted, primered and painted it Satin black. Probably not the most dureable finish, but satin black seemed like the right colour choice. The brown sticker was carefully removed with a sharp blade then double sided taped back on, and the..."

Post #6982 | Monday, 02-Jan 2012 @ 11:41am

Edited by beetwenty
Monday, 02-Jan 2012 @ 11:42am

Beetwenty's B10 2 door | Read full post

ThouUte

Toowoomba QLD

Joined: 10-Feb 2011

565 posts

Post #6983 | Monday, 02-Jan 2012 @ 11:36am

"sweet is that re-painted to?"

Beetwenty's B10 2 door | Read full post

Gold Coast, Australia

Joined: 05-Feb 2011

"I fixed up a heater for my car yesterday and today. Pics... I ended up using self adhesive foam tape to replace the foam on my vents and to seal up the main air inlet on the back. Im not sure if I will use this on my 1000 yet. I would like to..."

Post #6984 | Monday, 02-Jan 2012 @ 11:31am

Edited by beetwenty
Monday, 02-Jan 2012 @ 11:38am

Beetwenty's B10 2 door | Read full post

Gold Coast, Australia

Joined: 05-Feb 2011

"Thanks Dundee, As promised here are some pics of my under dash speaker set up. The ledge on the bottom of the dash wedges inbetween the speaker and mounting plate, and I ran a small 90deg bracket to the hood release cable mount. I did a similar..."

Post #6985 | Monday, 02-Jan 2012 @ 11:26am

Question about wiring | Read full post

three hills alberta canada

Joined: 11-Feb 2011

"No clue some one closer. Or maybe my friend did get it for me. we shal see"

Post #6986 | Monday, 02-Jan 2012 @ 10:59am

panasport rims | Read full post

d

Oz + JPN

Joined: 23-Apr 2011

1432 posts

Post #6987 | Monday, 02-Jan 2012 @ 10:47am

"you can use many 13s from also the 180b which are like bigger versions of the 12s and easier to find otherwise I would recomend these steelies they are quite nice and something different 14 x 6. ..."

Offset Question | Read full post

Rabaul, Papua New Guinea

Joined: 10-Feb 2011

Post #6988 | Monday, 02-Jan 2012 @ 10:19am

"To.....?"

panasport rims | Read full post

three hills alberta canada

Joined: 11-Feb 2011

Post #6989 | Monday, 02-Jan 2012 @ 10:13am

"They sold."

panasport rims | Read full post

Rabaul, Papua New Guinea

Joined: 10-Feb 2011

"Do 12inchers fit over the sigma brakes? I thought it were too tight. If you put your offset further in toward the vehicle (on the inside of the centreline) doesn't that mean you are adding width to the tread but not creating any dish? You're creating..."

Post #6990 | Monday, 02-Jan 2012 @ 10:13am

Edited by clyons8
Monday, 02-Jan 2012 @ 10:18am

Offset Question | Read full post

DatsAmore

Perth, Western Australia

Joined: 03-Dec 2011

239 posts

Post #6991 | Monday, 02-Jan 2012 @ 10:05am

"I'm looking at getting my standard steel rims widened to 6", to get that old skool deep dish steelies look. I'm aiming to have the tyre edge as close to the guard lip as possible, but not sure of what offset to use. If I have the offset the same..."

Offset Question | Read full post

Dundee1000

Fremantle

Joined: 11-Feb 2011

612 posts

Post #6992 | Monday, 02-Jan 2012 @ 9:53am

"Now that is a Good Harness Bro.. well done.."

Question about wiring | Read full post

DatsAmore

Perth, Western Australia

Joined: 03-Dec 2011

239 posts

Post #6993 | Monday, 02-Jan 2012 @ 9:46am

"Congrats revhead001, good to see they went to someone deserving. Here's to your 2012 being a better year than your 2011. Alan."

X-mas compitetion. | Read full post

Gold Coast, Australia

Joined: 05-Feb 2011

"The winner of our X-mas competition is revhead001 with a total of 4 votes. Congratulations Don, I'll get these sent off to you ASAP. Total votes ended as follows... DatsAmore (X1) rubeytuesday(X1) Dundee1000(X1) voted by rubeytuesday Botoneta(X1)..."

Post #6994 | Monday, 02-Jan 2012 @ 8:13am

Edited by beetwenty
Monday, 02-Jan 2012 @ 8:23am

X-mas compitetion. | Read full post

three hills alberta canada

Joined: 11-Feb 2011

"So little reading I figured that the back spacing on them are 100mm so it's right on the verge. http://alberta.kijiji.ca/c-cars-vehicles-auto-parts-tires-tires-rims-7-Lite-wheels-W0QQAdIdZ342092108. This is the add for the 7 inch rims both sets have a 4..."

Post #6995 | Sunday, 01-Jan 2012 @ 6:56pm

panasport rims | Read full post

revhead001

Melbourne

Joined: 09-Jul 2011

70 posts

Post #6996 | Sunday, 01-Jan 2012 @ 4:53pm

"My 13 x 5.5 watanabe's have a +17 offset and I have about 8mm clearence at the ball joint. But 13 x 6 is another thing all together. I tend to go off the backspace of the rim as it is more accurate for me. you need about 98mm to 100mm backspace for a rim..."

panasport rims | Read full post

Rabaul, Papua New Guinea

Joined: 10-Feb 2011

"25mm spacer is absolutely collossal, that is HUGE. The biggest I have run was 5mm. Why don't you find some wheels that actually fit? +25 is FWD territory. I think your limit is around +10 or +12 I know they're cheap but they don't fit. Spacers are..."

Post #6997 | Sunday, 01-Jan 2012 @ 3:44pm

panasport rims | Read full post

three hills alberta canada

Joined: 11-Feb 2011

"And yes that's seems right 25.8 mil would need 25 mil spacer for the fronts"

Post #6998 | Sunday, 01-Jan 2012 @ 2:37pm

panasport rims | Read full post

three hills alberta canada

Joined: 11-Feb 2011

"I'm not to sure on the offset I need to study a little more in that. I will get them anyways as they will prob fit my roadster no prob when I get it done."

Post #6999 | Sunday, 01-Jan 2012 @ 2:24pm

panasport rims | Read full post

Rabaul, Papua New Guinea

Joined: 10-Feb 2011